Arlington, MA · Middlesex County

Leaking Chimney Flashing in Arlington, MA

The joint where your chimney meets the roof fails before almost anything else on the house. We rebuild step and counter-flashing the right way — cut into the mortar, not smeared over it. Typical flashing repairs across Greater Boston run $400–$1,200, with full step-and-counter-flashing rebuilds on large chimneys or steep roofs pushing toward the top of that range.

Call (781) 653-5644

Most homeowners have never heard of NFPA 211, but it is quietly the reason a search like "leaking chimney flashing" has a well-established answer. NFPA 211 is the national standard governing chimneys, fireplaces, and venting systems, and it defines how these structures should be built, inspected, and maintained — including the three levels of inspection and the annual checkup every chimney should get. When something goes wrong with a chimney, the standard usually anticipated it. In this article, Upside Down Chimney Sweeps translates that industry knowledge into plain English for Massachusetts homeowners: what your symptom likely means, how a code-informed diagnosis works, what a correct repair looks like, and where corners tend to get cut. We are based in Melrose and serve Greater Boston; reach us anytime at (781) 653-5644.

Massachusetts homes are old — genuinely old, not real-estate-listing old. Triple-deckers from the 1890s, Victorians with three flues in one stack, postwar capes with hastily added fireplaces: each era brought its own construction habits, and many predate flue liners entirely. An unlined or deteriorated flue lets heat and gases reach parts of the house they were never meant to touch. That is why this issue deserves more attention in a Massachusetts home than the same symptom might get in a newer build elsewhere. The original masons did excellent work with the materials of their time, but no chimney was designed to go a century without attention, and most around Greater Boston have outlived their builders by decades. Understanding your chimney's era is the first step toward understanding what is going wrong with it.

Chimneys hide their problems better than almost any other part of a house. The flue interior is invisible without a camera. The crown is above the roofline where nobody looks. Flashing failures leak into wall cavities and show up as mysterious stains rooms away from the chimney. Even serious creosote accumulation is out of sight the moment you step back from the firebox. This is why homeowners are so often blindsided — not because they were careless, but because the evidence was structurally concealed. It is also why the chimney trade leans so heavily on scheduled inspections rather than wait-for-symptoms maintenance. By the time a chimney problem is visible from the living room, it has usually been developing for years. The search that brought you here may be the first visible edge of something older.

Chimney Flashing Repair in Arlington, MA

Around Boston, flashing dies in predictable ways. Galvanized steel rusts through — faster near the coast, where salt air is relentless. Counter-flashing that was surface-mounted with caulk instead of cut into the mortar peels away as the sealant fails. Nails back out of step flashing as the decking flexes through the seasons. Ice dams push meltwater up-slope and sideways, finding laps that shed downhill flow perfectly well. And on a remarkable number of roofs we inspect, someone has already answered a leak with roofing cement — a repair that buys a season or two, traps water behind it, and makes the eventual proper repair messier. If your chimney wears a black tar collar, water has been in there before.

Two parts of your house meet at the chimney's base, and they refuse to move together. The roof deck expands, contracts, and flexes with every temperature swing and snow load; the masonry chimney, anchored to its own foundation, barely moves at all. Any rigid seal between them is doomed from the day it is installed. That is the entire reason chimney flashing exists: instead of gluing the two structures together, a properly built flashing system overlaps layers of bent metal so water is shed by gravity while each layer stays free to move. Built right, it outlasts the shingles around it. Built wrong — or smeared over with tar — it becomes the single most common source of chimney leaks we see across Arlington.

Upside Down Chimney Sweeps rebuilds and repairs chimney flashing across Arlington and the surrounding Greater Boston area from our home base in Melrose. We work both sides of the joint — mason enough to cut and repoint reglets correctly, roof-literate enough to weave steps into shingle courses without wrecking the field around them. Flashing sits exactly at the boundary where roofers and masons tend to point at each other; we take responsibility for the whole intersection instead. If you have stains near the chimney, a visible tar patch on the roof, or a roofer who told you the chimney is the problem, call (781) 653-5644 and we will get experienced eyes on it.

What the Service Includes

1Full flashing evaluation

We inspect the entire roof-to-chimney intersection from both sides: on the roof, we check step flashing engagement, counter-flashing seating, apron condition, fastener back-out, and any previous tar or caulk repairs; in the attic, we examine the sheathing and rafters around the chase for staining, delamination, and active moisture with a meter. Because flashing failures mimic crown and masonry leaks, we rule those out rather than assume. You get photos of everything and a straight answer about whether flashing is truly your problem — sometimes it is not, and we say so.

2Step flashing replacement

When steps are rusted, missing, or face-nailed through their vertical legs, we replace them properly. Shingle courses alongside the chimney are carefully lifted or removed, the old metal comes out, and new L-shaped steps go in — one per course, each overlapping the piece below, fastened to the deck rather than the masonry so the roof can move freely. Where conditions warrant, we bed the intersection in self-adhering ice-and-water membrane first, which matters enormously on the snow-loaded, ice-dam-prone rooflines common across Massachusetts.

3Counter-flashing cut into the mortar

This is the detail that separates a proper job from a caulk job. We grind a clean reglet into the mortar joints, following the joint line up the chimney in steps, insert the counter-flashing's bent edge into the groove, wedge it mechanically, and seal the joint with the right sealant — used as a gasket inside a groove, not as glue on a surface. Counter-flashing installed this way is held by the chimney itself and sheds water over the step flashing below it for decades.

4Crickets and saddles for wide chimneys

A chimney more than about 30 inches wide creates a dam on its uphill side, where snow, ice, and debris pile up and water ponds. Building convention and modern code guidance call for a cricket: a small peaked saddle framed behind the chimney that splits the flow and sends it around both sides. We fabricate and flash crickets on chimneys that never had one — common on the older housing stock around Arlington — and rebuild failed ones. If your leak shows up on the chimney's high side, a missing cricket is a prime suspect.

5Material selection and upgrades

We work in aluminum, galvanized and stainless steel, copper, and lead-coated copper, and we will tell you honestly where each belongs. Aluminum is economical but should not sit against damp mortar for the long haul; copper costs more and can outlive two roofs; stainless shrugs off the coastal salt air that eats galvanized coatings in a decade. On historic homes we match existing copper work rather than mixing metals. The right choice depends on your roof's age, your budget, and your exposure — a coastal cape and an inland colonial do not get the same recommendation.

6Reglet repointing and roof integration

Flashing repair is masonry work as much as metal work. We repoint the joints we cut, match mortar color as closely as the wall allows, and address crumbling joints adjacent to the flashing line while we are up there — there is no sense seating new metal into failing mortar. We also coordinate cleanly with roofers: if your roof is being replaced, we can handle the chimney intersection as part of that project, and if we find shingle or decking problems beyond the flashing, we document them for your roofing contractor rather than pretending they do not exist.

How We Diagnose and Fix It

Here is what an actual diagnostic visit looks like, so you know what to expect. The sweep starts with questions — when the symptom appears, what changed recently, how you use the fireplace — because the history narrows the possibilities before a ladder comes off the truck. Then the physical inspection: firebox, damper, and smoke chamber from below; crown, cap, flashing, and masonry from the roof; a camera scan of the flue if the situation calls for one. Photos get taken throughout. At the end, you should receive a plain-language explanation of what was found, evidence you can see yourself, and a written scope if work is recommended. The whole process typically fits inside an hour or two. What you should not get is a verdict delivered from the driveway without anyone touching the chimney.

A well-run repair project follows a predictable arc. It starts with the inspection findings, documented in photos or video you can review yourself. From there, the contractor writes a scope: what will be done, with what materials, in what order, and what it costs — itemized so you can see where the money goes. Scheduling comes next, often shaped by weather, since masonry work has temperature requirements. On work day, expect drop cloths and dust control inside if the job touches the firebox or flue, and staging or roof access outside. Afterward, a reputable outfit walks you through what was done, ideally with after photos taken from the same angles as the before shots. For a project like flashing repair, that documentation trail is not bureaucracy — it is how you verify you got what you paid for.

Warning Signs to Watch For

Water stains on ceilings or walls adjacent to the chimney, especially after wind-driven rain.
Visible tar or roofing cement smeared around the chimney's base — evidence of a previous shortcut repair.
Rust streaks running from the chimney base down across the shingles.
Lifted, bent, or missing pieces of flashing after a windstorm.
Visible gaps between the counter-flashing and the mortar joint it should sit in.
Popped nails or loose fasteners along the flashing line.
Shingles that look wavy, curled, or spongy in the courses beside the chimney.
Attic sheathing that is dark, damp, or delaminating around the chimney — especially on its uphill side.
Leaks that appear during nor'easters but not during gentle vertical rain.
Moss or algae concentrated right at the roof-to-chimney intersection.

Why This Matters in Arlington

Arlington is dense with early-20th-century two-family homes, along with Victorians, colonials, and Philadelphia-style two-families built out between the 1890s and 1930s. Nearly all of this stock carries original brick chimneys, many serving multiple flues for separate units. A century of freeze-thaw cycles means crown cracks, spalling brick, and deteriorated mortar joints are everyday finds here.

Arlington Heights climbs some of the highest ground inside Route 128, and chimneys up on the hill catch more wind and weather than those near Spy Pond. Because so many homes are two-families, a single chimney often vents two households' heating systems, which raises the stakes on liner condition and regular inspection.

The single greatest enemy of masonry in Arlington is not fire; it is water paired with our freeze-thaw climate. Brick and mortar are porous, and every rain or melting snowfall lets moisture soak in. When temperatures drop below freezing, that trapped water expands roughly nine percent, prying the material apart from within. When it thaws, the water sinks deeper into the newly opened pores and waits to freeze again. Massachusetts winters can cycle above and below freezing dozens of times, and each cycle does its increment of damage. The visible result is spalling: brick faces popping off, mortar joints crumbling, and crowns cracking. Keeping water out of the masonry in the first place is why caps, crowns, and waterproofing earn their keep here.

What It Typically Costs

Homeowners reasonably want to know what drives the price of a chimney sweep, and the honest answer is a handful of concrete variables. The number of flues matters, since a chimney serving a fireplace, a furnace, and a wood stove is really three cleaning jobs in one stack. Height and roof access matter, because a steep slate roof changes the equipment and the time involved. Most of all, the condition of the deposits matters: first-stage creosote brushes out quickly, while glazed third-stage creosote requires specialized tools and considerably more labor. A sweep quoted sight-unseen at a suspiciously low price often becomes a different price on-site. We prefer to explain the variables up front and quote honestly.

Why Call Upside Down Chimney Sweeps

People ask about the name. Upside Down Chimney Sweeps comes from how we approach every job: from both ends. Plenty of problems hide from a technician working only at the hearth, and just as many hide from one working only on the roof. So we look up the flue from the firebox and down from the chimney top, check the crown and cap where weather attacks first, and examine the attic and rooflines where leaks leave their earliest evidence. Turning the routine upside down is a small discipline that catches the cracked tile, the failing flashing, and the nesting animals that a quicker visit would miss. It is a slightly odd name that stands for exactly the thoroughness you are hiring.

Frequently Asked Questions

What is chimney flashing, exactly?

Flashing is the layered sheet-metal system that waterproofs the joint where your chimney passes through the roof. Because the roof structure and the masonry move independently, no rigid or glued seal can survive there. Instead, flashing sheds water by overlapping: step flashing woven into the shingle courses carries water down the roof plane, and counter-flashing embedded in the chimney's mortar joints covers the tops of those steps so water running down the brick is thrown clear. Add an apron on the downhill face and a back pan or cricket uphill, and every side of the chimney has a gravity-fed drainage path. No adhesive is doing the real work — the geometry is.

What is the difference between step flashing and counter-flashing?

They are two layers with two jobs. Step flashing belongs to the roof: individual L-shaped pieces, one per shingle course, each tucked under a shingle and lapped over the piece below, fastened to the roof deck. It handles water flowing down the roof plane. Counter-flashing belongs to the chimney: pieces set into grooves cut in the mortar joints, bent down over the step flashing's vertical legs. It handles water flowing down the masonry face. The critical detail is that the two layers overlap without being attached to each other, so the roof and the chimney can move independently through the seasons without tearing the seal open.

Why not just seal it with roofing tar?

Roofing cement is a bandage, and everyone in this trade knows it. It bonds poorly to dusty masonry, turns brittle in the cold, shrinks away from edges within a couple of seasons, and — the part homeowners rarely hear — it can trap water behind it, holding moisture against the mortar through freeze-thaw cycles and accelerating the very damage it was hiding. It also buries the evidence, so the next diagnosis takes longer and costs more. We remove tar patches; we do not add to them. A proper counter-stepped metal system costs more on the day it is installed and dramatically less over the life of your roof.

Should I call a roofer or a chimney company for a flashing leak?

It is genuinely a boundary trade, which is why homeowners get bounced between the two. Roofers are excellent on the shingle side but often surface-mount counter-flashing with caulk rather than cutting it into the mortar, because masonry is not their trade. A chimney company that does masonry can cut reglets, repoint, and judge whether the leak is actually the crown or the brick rather than the flashing at all. We handle the full intersection and coordinate with your roofer when the job crosses into the roof field. Whoever you hire, ask one question: will the counter-flashing be let into the mortar joint? If the answer involves caulk, keep calling.

Which flashing metal is best, especially near the coast?

For most inland Greater Boston homes, aluminum or galvanized steel is serviceable and economical, but both have limits: aluminum reacts with damp mortar over time, and galvanized coatings fail early in salt air. Within a few miles of the ocean we push toward stainless steel or copper — coastal exposure corrodes cheap metal astonishingly fast, and we regularly replace galvanized flashing barely fifteen years old in shoreline towns. Copper is the premium choice everywhere: it forms beautifully, ages to a quiet brown, and routinely outlasts two shingle roofs. On historic homes in and around Arlington, matching existing copper work is usually the right call both structurally and visually.

What is a cricket, and does my chimney need one?

A cricket, or saddle, is a small peaked structure built on the uphill side of a chimney to split water and snow around it instead of letting the chimney act as a dam. Modern building practice calls for one when the chimney is wider than about 30 inches across the slope. Without a cricket, the high side collects leaves, snowpack, and ponded water, and that standing load eventually beats any flat back pan. Many chimneys on older Massachusetts homes were built without one, which is why chronic high-side leaks are so common here. If your stains are on the uphill side of the chimney, ask us to check for this first.

How long does the repair take, and how long will it last?

Most full flashing rebuilds are a one-day job; targeted repairs of a single failed section often take a few hours. Weather matters — we want dry shingles, workable temperatures for sealants and mortar, and safe footing, so winter scheduling can shift with the forecast. As for longevity: properly counter-stepped metal set into sound mortar should last as long as the roof itself, and copper considerably longer. The honest caveat is the surrounding masonry — flashing set into crumbling joints will never reach its potential, which is why we repoint the reglet line as part of the job rather than treating it as an upsell.

My roof is being replaced — should the flashing be redone at the same time?

Yes, almost always, and the timing is a gift: with the shingles off, the entire intersection is exposed, membrane can be run properly, and new step flashing costs the least it ever will. Reusing old step flashing under a new roof is a common corner-cut we would talk you out of — thirty-year shingles deserve better than twenty-year-old metal. Coordinate the sequence: we can cut reglets and set counter-flashing right after the roofer finishes the field, or handle the full chimney intersection ourselves as part of the project. Call (781) 653-5644 before the roofing crew starts and we will slot the chimney work into their schedule.

Get It Handled Today

If your chimney is due, or overdue, for attention, the next step is a short phone call. Reach Upside Down Chimney Sweeps at (781) 653-5644 and we will find a time that works, usually sooner than you might expect for Arlington addresses given how close we are. Tell us what you have noticed, or simply tell us it has been a while; either one is a fine place to start. One visit gets you a swept flue, a documented inspection, and straight answers about anything we find along the way. Your fireplace should be the most relaxing thing in your house, not a question mark hanging over it. Let us make sure it stays that way.

Serving Arlington Same-Week

Our Melrose shop is 7 miles from Arlington. Call (781) 653-5644 for fast scheduling.

Call (781) 653-5644 Email Us

Mon–Sat: 7:00 AM – 7:00 PM · Emergency service available