Sharon, MA · Norfolk County

Leak Around Chimney Flashing in Sharon, MA

The joint where your chimney meets the roof fails before almost anything else on the house. We rebuild step and counter-flashing the right way — cut into the mortar, not smeared over it. Typical flashing repairs across Greater Boston run $400–$1,200, with full step-and-counter-flashing rebuilds on large chimneys or steep roofs pushing toward the top of that range.

Call (781) 653-5644

New England winters are a stress test that most building materials eventually fail, and chimneys take the worst of it. They stand above the roofline, unprotected, through nor'easters, ice storms, and dozens of freeze-thaw cycles a season — all while channeling combustion gases hot enough to matter. So when a homeowner searches for "leak around chimney flashing" in Massachusetts, the weather is almost always part of the story. In this guide, Upside Down Chimney Sweeps explains how winter exposure creates or accelerates the problem behind your search, what a thorough diagnosis covers, and why certain repairs last here while others fail within a few seasons. We will also cover timing, because in this climate, when you do the work matters nearly as much as how. Talk to a sweep directly at (781) 653-5644.

Ask any experienced sweep to name the real enemy of chimneys and the answer will not be fire — it will be water. Masonry is porous. Rain and snowmelt soak into brick and mortar, and every time temperatures cross freezing, that trapped water expands roughly nine percent, prying material apart from the inside. In a Massachusetts winter, a single week can deliver several freeze-thaw cycles. The chimney's defenses against this — the crown on top, the cap over the flue, the flashing where brick meets roof, and breathable water repellents on the masonry face — all wear out on their own schedules. When any one fails, water gets in, and nearly every expensive chimney problem we see traces back to that moment. Whatever symptom brought you here, water is the first suspect worth ruling out.

In Massachusetts, a chimney is not seasonal decoration — it is infrastructure. The heating season here runs from October into April, and many chimneys serve double duty, venting a wood-burning fireplace on one flue and an oil or gas heating appliance on another. That means a chimney problem can compromise not just cozy fires but the system that keeps pipes from freezing in January. It also means the flues get real use: months of thermal cycling, condensation, and byproduct accumulation every single year. A problem that might stay dormant for a decade in a milder climate gets stress-tested here every winter. That is the practical reason Massachusetts homeowners cannot treat chimney symptoms casually — the season that reveals the problem is the same season you can least afford to lose the chimney.

Chimney Flashing Repair in Sharon, MA

Two parts of your house meet at the chimney's base, and they refuse to move together. The roof deck expands, contracts, and flexes with every temperature swing and snow load; the masonry chimney, anchored to its own foundation, barely moves at all. Any rigid seal between them is doomed from the day it is installed. That is the entire reason chimney flashing exists: instead of gluing the two structures together, a properly built flashing system overlaps layers of bent metal so water is shed by gravity while each layer stays free to move. Built right, it outlasts the shingles around it. Built wrong — or smeared over with tar — it becomes the single most common source of chimney leaks we see across Sharon.

A correct installation has distinct layers with distinct jobs. Step flashing consists of L-shaped pieces of metal, one woven into each course of shingles as the roof climbs past the chimney, so every piece hands water down onto the shingle below it. Counter-flashing is the second layer: metal let into a groove — a reglet — cut into the chimney's mortar joints, then bent down over the tops of the step pieces. This counter-stepped arrangement means water running down the brick face is thrown out over the steps, never behind them, and neither layer depends on adhesive to do its job. An apron protects the downhill face, and on the uphill side a back pan or cricket diverts the water the chimney dams up.

Upside Down Chimney Sweeps rebuilds and repairs chimney flashing across Sharon and the surrounding Greater Boston area from our home base in Melrose. We work both sides of the joint — mason enough to cut and repoint reglets correctly, roof-literate enough to weave steps into shingle courses without wrecking the field around them. Flashing sits exactly at the boundary where roofers and masons tend to point at each other; we take responsibility for the whole intersection instead. If you have stains near the chimney, a visible tar patch on the roof, or a roofer who told you the chimney is the problem, call (781) 653-5644 and we will get experienced eyes on it.

What the Service Includes

1Full flashing evaluation

We inspect the entire roof-to-chimney intersection from both sides: on the roof, we check step flashing engagement, counter-flashing seating, apron condition, fastener back-out, and any previous tar or caulk repairs; in the attic, we examine the sheathing and rafters around the chase for staining, delamination, and active moisture with a meter. Because flashing failures mimic crown and masonry leaks, we rule those out rather than assume. You get photos of everything and a straight answer about whether flashing is truly your problem — sometimes it is not, and we say so.

2Step flashing replacement

When steps are rusted, missing, or face-nailed through their vertical legs, we replace them properly. Shingle courses alongside the chimney are carefully lifted or removed, the old metal comes out, and new L-shaped steps go in — one per course, each overlapping the piece below, fastened to the deck rather than the masonry so the roof can move freely. Where conditions warrant, we bed the intersection in self-adhering ice-and-water membrane first, which matters enormously on the snow-loaded, ice-dam-prone rooflines common across Massachusetts.

3Counter-flashing cut into the mortar

This is the detail that separates a proper job from a caulk job. We grind a clean reglet into the mortar joints, following the joint line up the chimney in steps, insert the counter-flashing's bent edge into the groove, wedge it mechanically, and seal the joint with the right sealant — used as a gasket inside a groove, not as glue on a surface. Counter-flashing installed this way is held by the chimney itself and sheds water over the step flashing below it for decades.

4Crickets and saddles for wide chimneys

A chimney more than about 30 inches wide creates a dam on its uphill side, where snow, ice, and debris pile up and water ponds. Building convention and modern code guidance call for a cricket: a small peaked saddle framed behind the chimney that splits the flow and sends it around both sides. We fabricate and flash crickets on chimneys that never had one — common on the older housing stock around Sharon — and rebuild failed ones. If your leak shows up on the chimney's high side, a missing cricket is a prime suspect.

5Material selection and upgrades

We work in aluminum, galvanized and stainless steel, copper, and lead-coated copper, and we will tell you honestly where each belongs. Aluminum is economical but should not sit against damp mortar for the long haul; copper costs more and can outlive two roofs; stainless shrugs off the coastal salt air that eats galvanized coatings in a decade. On historic homes we match existing copper work rather than mixing metals. The right choice depends on your roof's age, your budget, and your exposure — a coastal cape and an inland colonial do not get the same recommendation.

6Reglet repointing and roof integration

Flashing repair is masonry work as much as metal work. We repoint the joints we cut, match mortar color as closely as the wall allows, and address crumbling joints adjacent to the flashing line while we are up there — there is no sense seating new metal into failing mortar. We also coordinate cleanly with roofers: if your roof is being replaced, we can handle the chimney intersection as part of that project, and if we find shingle or decking problems beyond the flashing, we document them for your roofing contractor rather than pretending they do not exist.

How We Diagnose and Fix It

The single biggest advance in chimney diagnosis is the flue camera. A chimney's interior used to be judged with a flashlight and a mirror from the bottom; today a sweep runs a camera the full height of the flue and sees every tile joint, crack, gap, and deposit in detail. This matters because flue damage is both invisible and consequential — a cracked tile or open mortar joint can expose framing to heat and gases without producing any symptom a homeowner would notice. When we scan a flue at Upside Down Chimney Sweeps, the homeowner can see the footage too, which turns the diagnosis from take-our-word-for-it into something you can evaluate yourself. If a contractor proposes significant interior work without camera evidence, it is entirely fair to ask why.

Professional creosote removal is matched to what the inspection found. Stage 1 and Stage 2 deposits come out with rotary or manual brushing sized to the flue, with the firebox sealed off and a HEPA vacuum controlling dust — a properly done sweep leaves no mess in the house. Stage 3 glaze is a different job: hardened, tarry creosote bonds to the flue and must be treated with specialized chemical modifiers that break it down over one or more applications before mechanical removal, and badly glazed flues sometimes force the relining conversation instead. After cleaning, the sweep verifies the flue with a light or camera pass. Equally important is the debrief: what the deposits indicated about wood quality, burn habits, and draft, so the conditions that built the creosote do not simply rebuild it.

Warning Signs to Watch For

Water stains on ceilings or walls adjacent to the chimney, especially after wind-driven rain.
Visible tar or roofing cement smeared around the chimney's base — evidence of a previous shortcut repair.
Rust streaks running from the chimney base down across the shingles.
Lifted, bent, or missing pieces of flashing after a windstorm.
Visible gaps between the counter-flashing and the mortar joint it should sit in.
Popped nails or loose fasteners along the flashing line.
Shingles that look wavy, curled, or spongy in the courses beside the chimney.
Attic sheathing that is dark, damp, or delaminating around the chimney — especially on its uphill side.
Leaks that appear during nor'easters but not during gentle vertical rain.
Moss or algae concentrated right at the roof-to-chimney intersection.

Why This Matters in Sharon

Sharon's housing runs to mid-century colonials and split-levels set on wooded lots, along with lakeside homes around Massapoag and newer construction on the town's edges. Fireplace ownership is high, and many wooded-lot homes carry a second flue for a wood stove. Tree cover keeps roofs and chimneys shaded and damp, so moss and spalled brick are frequent findings.

More than a third of Sharon is protected open space, anchored by Moose Hill, the oldest Mass Audubon sanctuary, and the town's elevated, heavily wooded terrain gives it a more rural feel than its Norfolk County neighbors. Wood heat is a practical choice on these lots and firewood is easy to come by. Overhanging trees also make chimney caps essential here to keep out squirrels and nesting birds.

The stretch of chimney above your roofline lives a harder life than any other masonry on a Sharon home. It takes weather from all four sides, gets no shelter from eaves or landscaping, and endures the sharpest temperature swings on the property, warmed from within by flue gases while winter air holds the exterior far below freezing. The crown, the concrete surface sealing the top of the stack, bears the worst of it and is often built too thin in the first place. Small crown cracks admit water directly into the chimney's core, where freeze-thaw pressure spreads the damage downward out of sight. This is why a professional inspection pays so much attention to the top three feet of a chimney.

What It Typically Costs

Homeowners reasonably want to know what drives the price of a chimney sweep, and the honest answer is a handful of concrete variables. The number of flues matters, since a chimney serving a fireplace, a furnace, and a wood stove is really three cleaning jobs in one stack. Height and roof access matter, because a steep slate roof changes the equipment and the time involved. Most of all, the condition of the deposits matters: first-stage creosote brushes out quickly, while glazed third-stage creosote requires specialized tools and considerably more labor. A sweep quoted sight-unseen at a suspiciously low price often becomes a different price on-site. We prefer to explain the variables up front and quote honestly.

Why Call Upside Down Chimney Sweeps

We built this company on the belief that chimney work should follow written standards, not folklore. Our sweeping and inspection procedures track NFPA 211, the National Fire Protection Association's standard for chimneys, fireplaces, and vents, along with the best practices promoted by the Chimney Safety Institute of America. That means we do not eyeball a flue and pronounce it fine; we examine accessible portions methodically, note the condition of liners, crowns, caps, and flashing, and classify creosote honestly by stage. Standards protect you in a second way, too: when we recommend a repair, we can point to the specific condition and the specific guidance behind the recommendation, so you are never asked to take an expensive claim on faith.

Frequently Asked Questions

What is chimney flashing, exactly?

Flashing is the layered sheet-metal system that waterproofs the joint where your chimney passes through the roof. Because the roof structure and the masonry move independently, no rigid or glued seal can survive there. Instead, flashing sheds water by overlapping: step flashing woven into the shingle courses carries water down the roof plane, and counter-flashing embedded in the chimney's mortar joints covers the tops of those steps so water running down the brick is thrown clear. Add an apron on the downhill face and a back pan or cricket uphill, and every side of the chimney has a gravity-fed drainage path. No adhesive is doing the real work — the geometry is.

What is the difference between step flashing and counter-flashing?

They are two layers with two jobs. Step flashing belongs to the roof: individual L-shaped pieces, one per shingle course, each tucked under a shingle and lapped over the piece below, fastened to the roof deck. It handles water flowing down the roof plane. Counter-flashing belongs to the chimney: pieces set into grooves cut in the mortar joints, bent down over the step flashing's vertical legs. It handles water flowing down the masonry face. The critical detail is that the two layers overlap without being attached to each other, so the roof and the chimney can move independently through the seasons without tearing the seal open.

Why not just seal it with roofing tar?

Roofing cement is a bandage, and everyone in this trade knows it. It bonds poorly to dusty masonry, turns brittle in the cold, shrinks away from edges within a couple of seasons, and — the part homeowners rarely hear — it can trap water behind it, holding moisture against the mortar through freeze-thaw cycles and accelerating the very damage it was hiding. It also buries the evidence, so the next diagnosis takes longer and costs more. We remove tar patches; we do not add to them. A proper counter-stepped metal system costs more on the day it is installed and dramatically less over the life of your roof.

Should I call a roofer or a chimney company for a flashing leak?

It is genuinely a boundary trade, which is why homeowners get bounced between the two. Roofers are excellent on the shingle side but often surface-mount counter-flashing with caulk rather than cutting it into the mortar, because masonry is not their trade. A chimney company that does masonry can cut reglets, repoint, and judge whether the leak is actually the crown or the brick rather than the flashing at all. We handle the full intersection and coordinate with your roofer when the job crosses into the roof field. Whoever you hire, ask one question: will the counter-flashing be let into the mortar joint? If the answer involves caulk, keep calling.

Which flashing metal is best, especially near the coast?

For most inland Greater Boston homes, aluminum or galvanized steel is serviceable and economical, but both have limits: aluminum reacts with damp mortar over time, and galvanized coatings fail early in salt air. Within a few miles of the ocean we push toward stainless steel or copper — coastal exposure corrodes cheap metal astonishingly fast, and we regularly replace galvanized flashing barely fifteen years old in shoreline towns. Copper is the premium choice everywhere: it forms beautifully, ages to a quiet brown, and routinely outlasts two shingle roofs. On historic homes in and around Sharon, matching existing copper work is usually the right call both structurally and visually.

What is a cricket, and does my chimney need one?

A cricket, or saddle, is a small peaked structure built on the uphill side of a chimney to split water and snow around it instead of letting the chimney act as a dam. Modern building practice calls for one when the chimney is wider than about 30 inches across the slope. Without a cricket, the high side collects leaves, snowpack, and ponded water, and that standing load eventually beats any flat back pan. Many chimneys on older Massachusetts homes were built without one, which is why chronic high-side leaks are so common here. If your stains are on the uphill side of the chimney, ask us to check for this first.

How long does the repair take, and how long will it last?

Most full flashing rebuilds are a one-day job; targeted repairs of a single failed section often take a few hours. Weather matters — we want dry shingles, workable temperatures for sealants and mortar, and safe footing, so winter scheduling can shift with the forecast. As for longevity: properly counter-stepped metal set into sound mortar should last as long as the roof itself, and copper considerably longer. The honest caveat is the surrounding masonry — flashing set into crumbling joints will never reach its potential, which is why we repoint the reglet line as part of the job rather than treating it as an upsell.

My roof is being replaced — should the flashing be redone at the same time?

Yes, almost always, and the timing is a gift: with the shingles off, the entire intersection is exposed, membrane can be run properly, and new step flashing costs the least it ever will. Reusing old step flashing under a new roof is a common corner-cut we would talk you out of — thirty-year shingles deserve better than twenty-year-old metal. Coordinate the sequence: we can cut reglets and set counter-flashing right after the roofer finishes the field, or handle the full chimney intersection ourselves as part of the project. Call (781) 653-5644 before the roofing crew starts and we will slot the chimney work into their schedule.

Get It Handled Today

You searched for leak around chimney flashing, and the search can end here. Upside Down Chimney Sweeps handles this work for Sharon homeowners regularly, following NFPA 211 standards, documenting everything with photographs, and explaining findings without jargon or pressure. Call (781) 653-5644 to talk through your situation with someone who does this every day; a few minutes on the phone is usually enough to scope the visit and set a time. We show up when promised, protect your home while we work, and stand behind the results. There are certainly bigger companies and flashier websites out there, but for careful chimney work done close to home, we like our chances of earning your call and then keeping your business.

Serving Sharon Same-Week

Our Melrose shop is 25 miles from Sharon. Call (781) 653-5644 for fast scheduling.

Call (781) 653-5644 Email Us

Mon–Sat: 7:00 AM – 7:00 PM · Emergency service available