Saugus, MA · Essex County

Leak Around Chimney Flashing in Saugus, MA

The joint where your chimney meets the roof fails before almost anything else on the house. We rebuild step and counter-flashing the right way — cut into the mortar, not smeared over it. Typical flashing repairs across Greater Boston run $400–$1,200, with full step-and-counter-flashing rebuilds on large chimneys or steep roofs pushing toward the top of that range.

Call (781) 653-5644

This article exists because "leak around chimney flashing" deserves a better answer than the internet usually provides. Chimney topics attract two kinds of content: vague filler written by people who have never held a brush, and alarmist pitches designed to frighten you into a contract. We are aiming for a third kind — the explanation a good sweep would give you across the kitchen table. Upside Down Chimney Sweeps is a Melrose, Massachusetts company, and everything below comes from work we actually perform in Greater Boston homes: the causes we find, the inspection process we follow, the repairs that hold up through New England winters, and the honest way to think about cost. Read on, and if anything raises a question about your own chimney, our number is (781) 653-5644.

Chimney problems compound in a way most home repairs do not. A roof leak generally stays a roof leak; a chimney defect recruits new ones. A cracked crown admits water, which spalls the top courses of brick, which opens mortar joints, which lets more water reach the flue tiles, which crack in turn — and suddenly a repair that once involved a trowel involves scaffolding. This cascade is the single best argument for acting early. In our experience around Greater Boston, the gap between catching a problem this season versus three seasons from now is frequently the difference between a minor line item and a partial rebuild. You do not need to panic over the issue that prompted your search, but you should resist the very human urge to file it under later.

In Massachusetts, a chimney is not seasonal decoration — it is infrastructure. The heating season here runs from October into April, and many chimneys serve double duty, venting a wood-burning fireplace on one flue and an oil or gas heating appliance on another. That means a chimney problem can compromise not just cozy fires but the system that keeps pipes from freezing in January. It also means the flues get real use: months of thermal cycling, condensation, and byproduct accumulation every single year. A problem that might stay dormant for a decade in a milder climate gets stress-tested here every winter. That is the practical reason Massachusetts homeowners cannot treat chimney symptoms casually — the season that reveals the problem is the same season you can least afford to lose the chimney.

Chimney Flashing Repair in Saugus, MA

Upside Down Chimney Sweeps rebuilds and repairs chimney flashing across Saugus and the surrounding Greater Boston area from our home base in Melrose. We work both sides of the joint — mason enough to cut and repoint reglets correctly, roof-literate enough to weave steps into shingle courses without wrecking the field around them. Flashing sits exactly at the boundary where roofers and masons tend to point at each other; we take responsibility for the whole intersection instead. If you have stains near the chimney, a visible tar patch on the roof, or a roofer who told you the chimney is the problem, call (781) 653-5644 and we will get experienced eyes on it.

A correct installation has distinct layers with distinct jobs. Step flashing consists of L-shaped pieces of metal, one woven into each course of shingles as the roof climbs past the chimney, so every piece hands water down onto the shingle below it. Counter-flashing is the second layer: metal let into a groove — a reglet — cut into the chimney's mortar joints, then bent down over the tops of the step pieces. This counter-stepped arrangement means water running down the brick face is thrown out over the steps, never behind them, and neither layer depends on adhesive to do its job. An apron protects the downhill face, and on the uphill side a back pan or cricket diverts the water the chimney dams up.

Around Boston, flashing dies in predictable ways. Galvanized steel rusts through — faster near the coast, where salt air is relentless. Counter-flashing that was surface-mounted with caulk instead of cut into the mortar peels away as the sealant fails. Nails back out of step flashing as the decking flexes through the seasons. Ice dams push meltwater up-slope and sideways, finding laps that shed downhill flow perfectly well. And on a remarkable number of roofs we inspect, someone has already answered a leak with roofing cement — a repair that buys a season or two, traps water behind it, and makes the eventual proper repair messier. If your chimney wears a black tar collar, water has been in there before.

What the Service Includes

1Full flashing evaluation

We inspect the entire roof-to-chimney intersection from both sides: on the roof, we check step flashing engagement, counter-flashing seating, apron condition, fastener back-out, and any previous tar or caulk repairs; in the attic, we examine the sheathing and rafters around the chase for staining, delamination, and active moisture with a meter. Because flashing failures mimic crown and masonry leaks, we rule those out rather than assume. You get photos of everything and a straight answer about whether flashing is truly your problem — sometimes it is not, and we say so.

2Step flashing replacement

When steps are rusted, missing, or face-nailed through their vertical legs, we replace them properly. Shingle courses alongside the chimney are carefully lifted or removed, the old metal comes out, and new L-shaped steps go in — one per course, each overlapping the piece below, fastened to the deck rather than the masonry so the roof can move freely. Where conditions warrant, we bed the intersection in self-adhering ice-and-water membrane first, which matters enormously on the snow-loaded, ice-dam-prone rooflines common across Massachusetts.

3Counter-flashing cut into the mortar

This is the detail that separates a proper job from a caulk job. We grind a clean reglet into the mortar joints, following the joint line up the chimney in steps, insert the counter-flashing's bent edge into the groove, wedge it mechanically, and seal the joint with the right sealant — used as a gasket inside a groove, not as glue on a surface. Counter-flashing installed this way is held by the chimney itself and sheds water over the step flashing below it for decades.

4Crickets and saddles for wide chimneys

A chimney more than about 30 inches wide creates a dam on its uphill side, where snow, ice, and debris pile up and water ponds. Building convention and modern code guidance call for a cricket: a small peaked saddle framed behind the chimney that splits the flow and sends it around both sides. We fabricate and flash crickets on chimneys that never had one — common on the older housing stock around Saugus — and rebuild failed ones. If your leak shows up on the chimney's high side, a missing cricket is a prime suspect.

5Material selection and upgrades

We work in aluminum, galvanized and stainless steel, copper, and lead-coated copper, and we will tell you honestly where each belongs. Aluminum is economical but should not sit against damp mortar for the long haul; copper costs more and can outlive two roofs; stainless shrugs off the coastal salt air that eats galvanized coatings in a decade. On historic homes we match existing copper work rather than mixing metals. The right choice depends on your roof's age, your budget, and your exposure — a coastal cape and an inland colonial do not get the same recommendation.

6Reglet repointing and roof integration

Flashing repair is masonry work as much as metal work. We repoint the joints we cut, match mortar color as closely as the wall allows, and address crumbling joints adjacent to the flashing line while we are up there — there is no sense seating new metal into failing mortar. We also coordinate cleanly with roofers: if your roof is being replaced, we can handle the chimney intersection as part of that project, and if we find shingle or decking problems beyond the flashing, we document them for your roofing contractor rather than pretending they do not exist.

How We Diagnose and Fix It

The single biggest advance in chimney diagnosis is the flue camera. A chimney's interior used to be judged with a flashlight and a mirror from the bottom; today a sweep runs a camera the full height of the flue and sees every tile joint, crack, gap, and deposit in detail. This matters because flue damage is both invisible and consequential — a cracked tile or open mortar joint can expose framing to heat and gases without producing any symptom a homeowner would notice. When we scan a flue at Upside Down Chimney Sweeps, the homeowner can see the footage too, which turns the diagnosis from take-our-word-for-it into something you can evaluate yourself. If a contractor proposes significant interior work without camera evidence, it is entirely fair to ask why.

When a flue can no longer safely contain heat and gases — cracked tiles, open joints, or no liner at all — relining is the fix, and stainless steel is the workhorse solution. The process: the flue is measured and the liner sized to the appliance it serves, because an oversized flue drafts poorly and condenses creosote. The stainless liner is lowered down the chimney, connected to the appliance or fireplace below, insulated in most cases to improve draft and meet listing requirements, and finished with a top plate and cap. Done properly, it creates a continuous, sealed, correctly sized passage from appliance to sky. Relining sounds invasive but usually takes about a day, involves no demolition in most homes, and is frequently the single most consequential safety upgrade an older Massachusetts chimney can receive.

Warning Signs to Watch For

Water stains on ceilings or walls adjacent to the chimney, especially after wind-driven rain.
Visible tar or roofing cement smeared around the chimney's base — evidence of a previous shortcut repair.
Rust streaks running from the chimney base down across the shingles.
Lifted, bent, or missing pieces of flashing after a windstorm.
Visible gaps between the counter-flashing and the mortar joint it should sit in.
Popped nails or loose fasteners along the flashing line.
Shingles that look wavy, curled, or spongy in the courses beside the chimney.
Attic sheathing that is dark, damp, or delaminating around the chimney — especially on its uphill side.
Leaks that appear during nor'easters but not during gentle vertical rain.
Moss or algae concentrated right at the roof-to-chimney intersection.

Why This Matters in Saugus

Saugus is largely a postwar town of capes, ranches, and split-levels built in the 1950s and 1960s, most carrying a single brick fireplace chimney now past sixty years old. Older Victorians and two-families cluster near Saugus Center and Cliftondale Square. Original clay flue tiles and washed-out crowns are the most common findings on the postwar stock.

Iron making in America began at the Saugus Iron Works in 1646, a fitting bit of history for a town we visit constantly with steel liners in the truck. Saugus borders Melrose directly, making it one of our fastest response areas. Homes near the Rumney Marsh side of town also pick up a measure of coastal air off the salt marsh.

The single greatest enemy of masonry in Saugus is not fire; it is water paired with our freeze-thaw climate. Brick and mortar are porous, and every rain or melting snowfall lets moisture soak in. When temperatures drop below freezing, that trapped water expands roughly nine percent, prying the material apart from within. When it thaws, the water sinks deeper into the newly opened pores and waits to freeze again. Massachusetts winters can cycle above and below freezing dozens of times, and each cycle does its increment of damage. The visible result is spalling: brick faces popping off, mortar joints crumbling, and crowns cracking. Keeping water out of the masonry in the first place is why caps, crowns, and waterproofing earn their keep here.

What It Typically Costs

Homeowners reasonably want to know what drives the price of a chimney sweep, and the honest answer is a handful of concrete variables. The number of flues matters, since a chimney serving a fireplace, a furnace, and a wood stove is really three cleaning jobs in one stack. Height and roof access matter, because a steep slate roof changes the equipment and the time involved. Most of all, the condition of the deposits matters: first-stage creosote brushes out quickly, while glazed third-stage creosote requires specialized tools and considerably more labor. A sweep quoted sight-unseen at a suspiciously low price often becomes a different price on-site. We prefer to explain the variables up front and quote honestly.

Why Call Upside Down Chimney Sweeps

Good chimney work starts with good communication, and we structure every job around it. Before we begin, you get a clear scope and a clear price. During the visit, our technician explains what they are finding and photographs anything noteworthy inside the flue or up on the roof, places you would never see otherwise. Afterward, you receive a report that plainly states the condition of your chimney and any recommendations, ranked by urgency. Call our office and a person who knows your job answers, not a call center reading a script. None of this is revolutionary; it is simply how service companies used to operate, and we think Greater Boston homeowners deserve contractors who still work that way.

Frequently Asked Questions

What is chimney flashing, exactly?

Flashing is the layered sheet-metal system that waterproofs the joint where your chimney passes through the roof. Because the roof structure and the masonry move independently, no rigid or glued seal can survive there. Instead, flashing sheds water by overlapping: step flashing woven into the shingle courses carries water down the roof plane, and counter-flashing embedded in the chimney's mortar joints covers the tops of those steps so water running down the brick is thrown clear. Add an apron on the downhill face and a back pan or cricket uphill, and every side of the chimney has a gravity-fed drainage path. No adhesive is doing the real work — the geometry is.

What is the difference between step flashing and counter-flashing?

They are two layers with two jobs. Step flashing belongs to the roof: individual L-shaped pieces, one per shingle course, each tucked under a shingle and lapped over the piece below, fastened to the roof deck. It handles water flowing down the roof plane. Counter-flashing belongs to the chimney: pieces set into grooves cut in the mortar joints, bent down over the step flashing's vertical legs. It handles water flowing down the masonry face. The critical detail is that the two layers overlap without being attached to each other, so the roof and the chimney can move independently through the seasons without tearing the seal open.

Why not just seal it with roofing tar?

Roofing cement is a bandage, and everyone in this trade knows it. It bonds poorly to dusty masonry, turns brittle in the cold, shrinks away from edges within a couple of seasons, and — the part homeowners rarely hear — it can trap water behind it, holding moisture against the mortar through freeze-thaw cycles and accelerating the very damage it was hiding. It also buries the evidence, so the next diagnosis takes longer and costs more. We remove tar patches; we do not add to them. A proper counter-stepped metal system costs more on the day it is installed and dramatically less over the life of your roof.

Should I call a roofer or a chimney company for a flashing leak?

It is genuinely a boundary trade, which is why homeowners get bounced between the two. Roofers are excellent on the shingle side but often surface-mount counter-flashing with caulk rather than cutting it into the mortar, because masonry is not their trade. A chimney company that does masonry can cut reglets, repoint, and judge whether the leak is actually the crown or the brick rather than the flashing at all. We handle the full intersection and coordinate with your roofer when the job crosses into the roof field. Whoever you hire, ask one question: will the counter-flashing be let into the mortar joint? If the answer involves caulk, keep calling.

Which flashing metal is best, especially near the coast?

For most inland Greater Boston homes, aluminum or galvanized steel is serviceable and economical, but both have limits: aluminum reacts with damp mortar over time, and galvanized coatings fail early in salt air. Within a few miles of the ocean we push toward stainless steel or copper — coastal exposure corrodes cheap metal astonishingly fast, and we regularly replace galvanized flashing barely fifteen years old in shoreline towns. Copper is the premium choice everywhere: it forms beautifully, ages to a quiet brown, and routinely outlasts two shingle roofs. On historic homes in and around Saugus, matching existing copper work is usually the right call both structurally and visually.

What is a cricket, and does my chimney need one?

A cricket, or saddle, is a small peaked structure built on the uphill side of a chimney to split water and snow around it instead of letting the chimney act as a dam. Modern building practice calls for one when the chimney is wider than about 30 inches across the slope. Without a cricket, the high side collects leaves, snowpack, and ponded water, and that standing load eventually beats any flat back pan. Many chimneys on older Massachusetts homes were built without one, which is why chronic high-side leaks are so common here. If your stains are on the uphill side of the chimney, ask us to check for this first.

How long does the repair take, and how long will it last?

Most full flashing rebuilds are a one-day job; targeted repairs of a single failed section often take a few hours. Weather matters — we want dry shingles, workable temperatures for sealants and mortar, and safe footing, so winter scheduling can shift with the forecast. As for longevity: properly counter-stepped metal set into sound mortar should last as long as the roof itself, and copper considerably longer. The honest caveat is the surrounding masonry — flashing set into crumbling joints will never reach its potential, which is why we repoint the reglet line as part of the job rather than treating it as an upsell.

My roof is being replaced — should the flashing be redone at the same time?

Yes, almost always, and the timing is a gift: with the shingles off, the entire intersection is exposed, membrane can be run properly, and new step flashing costs the least it ever will. Reusing old step flashing under a new roof is a common corner-cut we would talk you out of — thirty-year shingles deserve better than twenty-year-old metal. Coordinate the sequence: we can cut reglets and set counter-flashing right after the roofer finishes the field, or handle the full chimney intersection ourselves as part of the project. Call (781) 653-5644 before the roofing crew starts and we will slot the chimney work into their schedule.

Get It Handled Today

Here is our closing pitch, such as it is: no pressure, just an honest look. Call Upside Down Chimney Sweeps at (781) 653-5644 and schedule an inspection for your Saugus home. We will examine the chimney from top to bottom, show you photographs of what we find, and give you a written assessment with a clear estimate for any recommended work. Then the decisions are yours, made on evidence, on your timeline, with no obligation beyond the visit itself. If you want a second opinion, we welcome the comparison; our documentation travels well. That is the whole offer. We think it is how chimney service ought to work, and we would be glad to prove it at your house.

Serving Saugus Same-Week

Our Melrose shop is 3 miles from Saugus. Call (781) 653-5644 for fast scheduling.

Call (781) 653-5644 Email Us

Mon–Sat: 7:00 AM – 7:00 PM · Emergency service available