Pembroke, MA · Plymouth County

Chimney Flashing Repair Near me in Pembroke, MA

The joint where your chimney meets the roof fails before almost anything else on the house. We rebuild step and counter-flashing the right way — cut into the mortar, not smeared over it. Typical flashing repairs across Greater Boston run $400–$1,200, with full step-and-counter-flashing rebuilds on large chimneys or steep roofs pushing toward the top of that range.

Call (781) 653-5644

Massachusetts has some of the oldest housing stock in the country, and that history is a big part of why searches like "chimney flashing repair near me" are so common here. A chimney built in 1910 was designed for coal or wood heat and open fireplaces, not for modern appliances, modern fuels, or a century of freeze-thaw weathering. Many local chimneys still have unlined flues or original terra-cotta tiles well past their service life. So if you are dealing with this problem in an older home, you are in familiar territory for our crews. In this article, Upside Down Chimney Sweeps explains what is likely happening inside and outside your chimney, how age changes the diagnosis, and what a lasting repair looks like. Questions along the way? Call our Melrose office at (781) 653-5644.

Massachusetts homes are old — genuinely old, not real-estate-listing old. Triple-deckers from the 1890s, Victorians with three flues in one stack, postwar capes with hastily added fireplaces: each era brought its own construction habits, and many predate flue liners entirely. An unlined or deteriorated flue lets heat and gases reach parts of the house they were never meant to touch. That is why this issue deserves more attention in a Massachusetts home than the same symptom might get in a newer build elsewhere. The original masons did excellent work with the materials of their time, but no chimney was designed to go a century without attention, and most around Greater Boston have outlived their builders by decades. Understanding your chimney's era is the first step toward understanding what is going wrong with it.

In Massachusetts, a chimney is not seasonal decoration — it is infrastructure. The heating season here runs from October into April, and many chimneys serve double duty, venting a wood-burning fireplace on one flue and an oil or gas heating appliance on another. That means a chimney problem can compromise not just cozy fires but the system that keeps pipes from freezing in January. It also means the flues get real use: months of thermal cycling, condensation, and byproduct accumulation every single year. A problem that might stay dormant for a decade in a milder climate gets stress-tested here every winter. That is the practical reason Massachusetts homeowners cannot treat chimney symptoms casually — the season that reveals the problem is the same season you can least afford to lose the chimney.

Chimney Flashing Repair in Pembroke, MA

A correct installation has distinct layers with distinct jobs. Step flashing consists of L-shaped pieces of metal, one woven into each course of shingles as the roof climbs past the chimney, so every piece hands water down onto the shingle below it. Counter-flashing is the second layer: metal let into a groove — a reglet — cut into the chimney's mortar joints, then bent down over the tops of the step pieces. This counter-stepped arrangement means water running down the brick face is thrown out over the steps, never behind them, and neither layer depends on adhesive to do its job. An apron protects the downhill face, and on the uphill side a back pan or cricket diverts the water the chimney dams up.

Two parts of your house meet at the chimney's base, and they refuse to move together. The roof deck expands, contracts, and flexes with every temperature swing and snow load; the masonry chimney, anchored to its own foundation, barely moves at all. Any rigid seal between them is doomed from the day it is installed. That is the entire reason chimney flashing exists: instead of gluing the two structures together, a properly built flashing system overlaps layers of bent metal so water is shed by gravity while each layer stays free to move. Built right, it outlasts the shingles around it. Built wrong — or smeared over with tar — it becomes the single most common source of chimney leaks we see across Pembroke.

Upside Down Chimney Sweeps rebuilds and repairs chimney flashing across Pembroke and the surrounding Greater Boston area from our home base in Melrose. We work both sides of the joint — mason enough to cut and repoint reglets correctly, roof-literate enough to weave steps into shingle courses without wrecking the field around them. Flashing sits exactly at the boundary where roofers and masons tend to point at each other; we take responsibility for the whole intersection instead. If you have stains near the chimney, a visible tar patch on the roof, or a roofer who told you the chimney is the problem, call (781) 653-5644 and we will get experienced eyes on it.

What the Service Includes

1Full flashing evaluation

We inspect the entire roof-to-chimney intersection from both sides: on the roof, we check step flashing engagement, counter-flashing seating, apron condition, fastener back-out, and any previous tar or caulk repairs; in the attic, we examine the sheathing and rafters around the chase for staining, delamination, and active moisture with a meter. Because flashing failures mimic crown and masonry leaks, we rule those out rather than assume. You get photos of everything and a straight answer about whether flashing is truly your problem — sometimes it is not, and we say so.

2Step flashing replacement

When steps are rusted, missing, or face-nailed through their vertical legs, we replace them properly. Shingle courses alongside the chimney are carefully lifted or removed, the old metal comes out, and new L-shaped steps go in — one per course, each overlapping the piece below, fastened to the deck rather than the masonry so the roof can move freely. Where conditions warrant, we bed the intersection in self-adhering ice-and-water membrane first, which matters enormously on the snow-loaded, ice-dam-prone rooflines common across Massachusetts.

3Counter-flashing cut into the mortar

This is the detail that separates a proper job from a caulk job. We grind a clean reglet into the mortar joints, following the joint line up the chimney in steps, insert the counter-flashing's bent edge into the groove, wedge it mechanically, and seal the joint with the right sealant — used as a gasket inside a groove, not as glue on a surface. Counter-flashing installed this way is held by the chimney itself and sheds water over the step flashing below it for decades.

4Crickets and saddles for wide chimneys

A chimney more than about 30 inches wide creates a dam on its uphill side, where snow, ice, and debris pile up and water ponds. Building convention and modern code guidance call for a cricket: a small peaked saddle framed behind the chimney that splits the flow and sends it around both sides. We fabricate and flash crickets on chimneys that never had one — common on the older housing stock around Pembroke — and rebuild failed ones. If your leak shows up on the chimney's high side, a missing cricket is a prime suspect.

5Material selection and upgrades

We work in aluminum, galvanized and stainless steel, copper, and lead-coated copper, and we will tell you honestly where each belongs. Aluminum is economical but should not sit against damp mortar for the long haul; copper costs more and can outlive two roofs; stainless shrugs off the coastal salt air that eats galvanized coatings in a decade. On historic homes we match existing copper work rather than mixing metals. The right choice depends on your roof's age, your budget, and your exposure — a coastal cape and an inland colonial do not get the same recommendation.

6Reglet repointing and roof integration

Flashing repair is masonry work as much as metal work. We repoint the joints we cut, match mortar color as closely as the wall allows, and address crumbling joints adjacent to the flashing line while we are up there — there is no sense seating new metal into failing mortar. We also coordinate cleanly with roofers: if your roof is being replaced, we can handle the chimney intersection as part of that project, and if we find shingle or decking problems beyond the flashing, we document them for your roofing contractor rather than pretending they do not exist.

How We Diagnose and Fix It

When the problem involves a wood-burning flue, diagnosis includes assessing creosote, which the trade grades in three stages. Stage 1 is light, sooty, and brushes out easily — the normal product of good burning habits. Stage 2 is harder, flakier, and shinier, requiring more aggressive tools. Stage 3 is the serious one: a glazed, tar-like coating that has hardened onto the flue, cannot be removed with brushes alone, and is highly flammable — the primary fuel in chimney fires. The stage determines both the removal method and the urgency. A sweep will also read what the creosote says about cause: heavy glaze often points to smoldering fires, unseasoned wood, or a flue that is oversized or running too cool for its appliance. Cleaning without correcting the cause just schedules the next buildup.

How a job ends matters as much as how it begins. Before final payment on significant chimney work, you should see evidence: after photos from the roof, camera footage for any interior flue work, and a walkthrough of what was done against the written scope. Materials should be identified specifically — the mortar type, the liner alloy and insulation, the sealant product — because those details determine lifespan and warranty. Ask what the warranty covers and get it in writing; established manufacturers back stainless liners and masonry water repellents with meaningful terms when installed correctly. Finally, the paperwork joins your home's records, where it pays dividends at sale time and with your insurer. Work like flashing repair is invisible from the curb when done well, which is exactly why the documentation has to do the showing.

Warning Signs to Watch For

Water stains on ceilings or walls adjacent to the chimney, especially after wind-driven rain.
Visible tar or roofing cement smeared around the chimney's base — evidence of a previous shortcut repair.
Rust streaks running from the chimney base down across the shingles.
Lifted, bent, or missing pieces of flashing after a windstorm.
Visible gaps between the counter-flashing and the mortar joint it should sit in.
Popped nails or loose fasteners along the flashing line.
Shingles that look wavy, curled, or spongy in the courses beside the chimney.
Attic sheathing that is dark, damp, or delaminating around the chimney — especially on its uphill side.
Leaks that appear during nor'easters but not during gentle vertical rain.
Moss or algae concentrated right at the roof-to-chimney intersection.

Why This Matters in Pembroke

A good share of Pembroke's housing began as seasonal cottages around Furnace Pond, Oldham Pond, and the town's other ponds, later winterized into year-round homes, often with retrofit wood stoves and added flues. Mid-century capes and ranches line the older roads, while colonial-style subdivisions from the 1980s onward fill the rest. Retrofit stove installations here deserve close inspection.

Pembroke keeps a semi-rural, ponds-and-bogs character, with cranberry bogs still working and a herring run at Luddam's Ford each spring. Wood-stove heating is common and many homes burn through several cords a winter, so creosote buildup is a recurring issue. Converted lake cottages often have undersized or improvised chimneys that were never designed for daily winter burning.

Nor'easters give chimneys in Pembroke a beating that ordinary storms never match. These coastal systems drive rain and snow horizontally for hours at a time, forcing water against the sides of a chimney rather than politely down onto its cap. Wind-driven rain exploits every weakness: hairline cracks in the crown, thin spots in mortar joints, and lifted flashing at the roofline all become entry points under that kind of pressure. Homeowners often discover the aftermath weeks later, as a ceiling stain near the chimney or a damp, smoky odor in the firebox. After a hard nor'easter season, a careful inspection of the crown, flashing, and masonry is not paranoia; it is how storm damage gets caught while the fix is still small.

What It Typically Costs

Homeowners reasonably want to know what drives the price of a chimney sweep, and the honest answer is a handful of concrete variables. The number of flues matters, since a chimney serving a fireplace, a furnace, and a wood stove is really three cleaning jobs in one stack. Height and roof access matter, because a steep slate roof changes the equipment and the time involved. Most of all, the condition of the deposits matters: first-stage creosote brushes out quickly, while glazed third-stage creosote requires specialized tools and considerably more labor. A sweep quoted sight-unseen at a suspiciously low price often becomes a different price on-site. We prefer to explain the variables up front and quote honestly.

Why Call Upside Down Chimney Sweeps

One thing homeowners appreciate about Upside Down Chimney Sweeps is that we handle the whole chimney, not just one slice of it. Sweeping, camera inspections, cap and damper replacement, crown repair, flashing, waterproofing, repointing, liner installation, and full rebuilds all live under one roof. That breadth matters because chimney problems rarely respect trade boundaries: a leak may involve the flashing, the crown, and the mortar joints all at once, and a company that only sells one fix tends to see only one cause. Because we diagnose and repair across the entire system, we can recommend the remedy the chimney needs rather than the one we happen to offer. Fewer handoffs also means one point of accountability from first call to final walkthrough.

Frequently Asked Questions

What is chimney flashing, exactly?

Flashing is the layered sheet-metal system that waterproofs the joint where your chimney passes through the roof. Because the roof structure and the masonry move independently, no rigid or glued seal can survive there. Instead, flashing sheds water by overlapping: step flashing woven into the shingle courses carries water down the roof plane, and counter-flashing embedded in the chimney's mortar joints covers the tops of those steps so water running down the brick is thrown clear. Add an apron on the downhill face and a back pan or cricket uphill, and every side of the chimney has a gravity-fed drainage path. No adhesive is doing the real work — the geometry is.

What is the difference between step flashing and counter-flashing?

They are two layers with two jobs. Step flashing belongs to the roof: individual L-shaped pieces, one per shingle course, each tucked under a shingle and lapped over the piece below, fastened to the roof deck. It handles water flowing down the roof plane. Counter-flashing belongs to the chimney: pieces set into grooves cut in the mortar joints, bent down over the step flashing's vertical legs. It handles water flowing down the masonry face. The critical detail is that the two layers overlap without being attached to each other, so the roof and the chimney can move independently through the seasons without tearing the seal open.

Why not just seal it with roofing tar?

Roofing cement is a bandage, and everyone in this trade knows it. It bonds poorly to dusty masonry, turns brittle in the cold, shrinks away from edges within a couple of seasons, and — the part homeowners rarely hear — it can trap water behind it, holding moisture against the mortar through freeze-thaw cycles and accelerating the very damage it was hiding. It also buries the evidence, so the next diagnosis takes longer and costs more. We remove tar patches; we do not add to them. A proper counter-stepped metal system costs more on the day it is installed and dramatically less over the life of your roof.

Should I call a roofer or a chimney company for a flashing leak?

It is genuinely a boundary trade, which is why homeowners get bounced between the two. Roofers are excellent on the shingle side but often surface-mount counter-flashing with caulk rather than cutting it into the mortar, because masonry is not their trade. A chimney company that does masonry can cut reglets, repoint, and judge whether the leak is actually the crown or the brick rather than the flashing at all. We handle the full intersection and coordinate with your roofer when the job crosses into the roof field. Whoever you hire, ask one question: will the counter-flashing be let into the mortar joint? If the answer involves caulk, keep calling.

Which flashing metal is best, especially near the coast?

For most inland Greater Boston homes, aluminum or galvanized steel is serviceable and economical, but both have limits: aluminum reacts with damp mortar over time, and galvanized coatings fail early in salt air. Within a few miles of the ocean we push toward stainless steel or copper — coastal exposure corrodes cheap metal astonishingly fast, and we regularly replace galvanized flashing barely fifteen years old in shoreline towns. Copper is the premium choice everywhere: it forms beautifully, ages to a quiet brown, and routinely outlasts two shingle roofs. On historic homes in and around Pembroke, matching existing copper work is usually the right call both structurally and visually.

What is a cricket, and does my chimney need one?

A cricket, or saddle, is a small peaked structure built on the uphill side of a chimney to split water and snow around it instead of letting the chimney act as a dam. Modern building practice calls for one when the chimney is wider than about 30 inches across the slope. Without a cricket, the high side collects leaves, snowpack, and ponded water, and that standing load eventually beats any flat back pan. Many chimneys on older Massachusetts homes were built without one, which is why chronic high-side leaks are so common here. If your stains are on the uphill side of the chimney, ask us to check for this first.

How long does the repair take, and how long will it last?

Most full flashing rebuilds are a one-day job; targeted repairs of a single failed section often take a few hours. Weather matters — we want dry shingles, workable temperatures for sealants and mortar, and safe footing, so winter scheduling can shift with the forecast. As for longevity: properly counter-stepped metal set into sound mortar should last as long as the roof itself, and copper considerably longer. The honest caveat is the surrounding masonry — flashing set into crumbling joints will never reach its potential, which is why we repoint the reglet line as part of the job rather than treating it as an upsell.

My roof is being replaced — should the flashing be redone at the same time?

Yes, almost always, and the timing is a gift: with the shingles off, the entire intersection is exposed, membrane can be run properly, and new step flashing costs the least it ever will. Reusing old step flashing under a new roof is a common corner-cut we would talk you out of — thirty-year shingles deserve better than twenty-year-old metal. Coordinate the sequence: we can cut reglets and set counter-flashing right after the roofer finishes the field, or handle the full chimney intersection ourselves as part of the project. Call (781) 653-5644 before the roofing crew starts and we will slot the chimney work into their schedule.

Get It Handled Today

If your chimney is due, or overdue, for attention, the next step is a short phone call. Reach Upside Down Chimney Sweeps at (781) 653-5644 and we will find a time that works, usually sooner than you might expect for Pembroke addresses given how close we are. Tell us what you have noticed, or simply tell us it has been a while; either one is a fine place to start. One visit gets you a swept flue, a documented inspection, and straight answers about anything we find along the way. Your fireplace should be the most relaxing thing in your house, not a question mark hanging over it. Let us make sure it stays that way.

Serving Pembroke Same-Week

Our Melrose shop is 32 miles from Pembroke. Call (781) 653-5644 for fast scheduling.

Call (781) 653-5644 Email Us

Mon–Sat: 7:00 AM – 7:00 PM · Emergency service available