Malden, MA · Middlesex County

Chimney Flashing Repair Near me in Malden, MA

The joint where your chimney meets the roof fails before almost anything else on the house. We rebuild step and counter-flashing the right way — cut into the mortar, not smeared over it. Typical flashing repairs across Greater Boston run $400–$1,200, with full step-and-counter-flashing rebuilds on large chimneys or steep roofs pushing toward the top of that range.

Call (781) 653-5644

A surprising number of people searching for "chimney flashing repair near me" are not reacting to a symptom at all — they are reacting to paperwork. A home inspector flagged something during a sale. An insurance carrier asked questions after a claim. An appraiser noted the chimney's condition. Chimneys sit at an awkward intersection of safety, structure, and liability, which is why they show up in so many transactions. Whether your search started with paperwork or with an actual problem, the underlying questions are the same: what is wrong, how serious is it, and what does a proper fix involve? Upside Down Chimney Sweeps answers all three below, drawing on the standards — NFPA 211 inspections in particular — that inspectors and insurers rely on. For documentation you can actually hand to a third party, call (781) 653-5644.

Massachusetts homes are old — genuinely old, not real-estate-listing old. Triple-deckers from the 1890s, Victorians with three flues in one stack, postwar capes with hastily added fireplaces: each era brought its own construction habits, and many predate flue liners entirely. An unlined or deteriorated flue lets heat and gases reach parts of the house they were never meant to touch. That is why this issue deserves more attention in a Massachusetts home than the same symptom might get in a newer build elsewhere. The original masons did excellent work with the materials of their time, but no chimney was designed to go a century without attention, and most around Greater Boston have outlived their builders by decades. Understanding your chimney's era is the first step toward understanding what is going wrong with it.

Chimney problems compound in a way most home repairs do not. A roof leak generally stays a roof leak; a chimney defect recruits new ones. A cracked crown admits water, which spalls the top courses of brick, which opens mortar joints, which lets more water reach the flue tiles, which crack in turn — and suddenly a repair that once involved a trowel involves scaffolding. This cascade is the single best argument for acting early. In our experience around Greater Boston, the gap between catching a problem this season versus three seasons from now is frequently the difference between a minor line item and a partial rebuild. You do not need to panic over the issue that prompted your search, but you should resist the very human urge to file it under later.

Chimney Flashing Repair in Malden, MA

Two parts of your house meet at the chimney's base, and they refuse to move together. The roof deck expands, contracts, and flexes with every temperature swing and snow load; the masonry chimney, anchored to its own foundation, barely moves at all. Any rigid seal between them is doomed from the day it is installed. That is the entire reason chimney flashing exists: instead of gluing the two structures together, a properly built flashing system overlaps layers of bent metal so water is shed by gravity while each layer stays free to move. Built right, it outlasts the shingles around it. Built wrong — or smeared over with tar — it becomes the single most common source of chimney leaks we see across Malden.

Upside Down Chimney Sweeps rebuilds and repairs chimney flashing across Malden and the surrounding Greater Boston area from our home base in Melrose. We work both sides of the joint — mason enough to cut and repoint reglets correctly, roof-literate enough to weave steps into shingle courses without wrecking the field around them. Flashing sits exactly at the boundary where roofers and masons tend to point at each other; we take responsibility for the whole intersection instead. If you have stains near the chimney, a visible tar patch on the roof, or a roofer who told you the chimney is the problem, call (781) 653-5644 and we will get experienced eyes on it.

A correct installation has distinct layers with distinct jobs. Step flashing consists of L-shaped pieces of metal, one woven into each course of shingles as the roof climbs past the chimney, so every piece hands water down onto the shingle below it. Counter-flashing is the second layer: metal let into a groove — a reglet — cut into the chimney's mortar joints, then bent down over the tops of the step pieces. This counter-stepped arrangement means water running down the brick face is thrown out over the steps, never behind them, and neither layer depends on adhesive to do its job. An apron protects the downhill face, and on the uphill side a back pan or cricket diverts the water the chimney dams up.

What the Service Includes

1Full flashing evaluation

We inspect the entire roof-to-chimney intersection from both sides: on the roof, we check step flashing engagement, counter-flashing seating, apron condition, fastener back-out, and any previous tar or caulk repairs; in the attic, we examine the sheathing and rafters around the chase for staining, delamination, and active moisture with a meter. Because flashing failures mimic crown and masonry leaks, we rule those out rather than assume. You get photos of everything and a straight answer about whether flashing is truly your problem — sometimes it is not, and we say so.

2Step flashing replacement

When steps are rusted, missing, or face-nailed through their vertical legs, we replace them properly. Shingle courses alongside the chimney are carefully lifted or removed, the old metal comes out, and new L-shaped steps go in — one per course, each overlapping the piece below, fastened to the deck rather than the masonry so the roof can move freely. Where conditions warrant, we bed the intersection in self-adhering ice-and-water membrane first, which matters enormously on the snow-loaded, ice-dam-prone rooflines common across Massachusetts.

3Counter-flashing cut into the mortar

This is the detail that separates a proper job from a caulk job. We grind a clean reglet into the mortar joints, following the joint line up the chimney in steps, insert the counter-flashing's bent edge into the groove, wedge it mechanically, and seal the joint with the right sealant — used as a gasket inside a groove, not as glue on a surface. Counter-flashing installed this way is held by the chimney itself and sheds water over the step flashing below it for decades.

4Crickets and saddles for wide chimneys

A chimney more than about 30 inches wide creates a dam on its uphill side, where snow, ice, and debris pile up and water ponds. Building convention and modern code guidance call for a cricket: a small peaked saddle framed behind the chimney that splits the flow and sends it around both sides. We fabricate and flash crickets on chimneys that never had one — common on the older housing stock around Malden — and rebuild failed ones. If your leak shows up on the chimney's high side, a missing cricket is a prime suspect.

5Material selection and upgrades

We work in aluminum, galvanized and stainless steel, copper, and lead-coated copper, and we will tell you honestly where each belongs. Aluminum is economical but should not sit against damp mortar for the long haul; copper costs more and can outlive two roofs; stainless shrugs off the coastal salt air that eats galvanized coatings in a decade. On historic homes we match existing copper work rather than mixing metals. The right choice depends on your roof's age, your budget, and your exposure — a coastal cape and an inland colonial do not get the same recommendation.

6Reglet repointing and roof integration

Flashing repair is masonry work as much as metal work. We repoint the joints we cut, match mortar color as closely as the wall allows, and address crumbling joints adjacent to the flashing line while we are up there — there is no sense seating new metal into failing mortar. We also coordinate cleanly with roofers: if your roof is being replaced, we can handle the chimney intersection as part of that project, and if we find shingle or decking problems beyond the flashing, we document them for your roofing contractor rather than pretending they do not exist.

How We Diagnose and Fix It

Here is what an actual diagnostic visit looks like, so you know what to expect. The sweep starts with questions — when the symptom appears, what changed recently, how you use the fireplace — because the history narrows the possibilities before a ladder comes off the truck. Then the physical inspection: firebox, damper, and smoke chamber from below; crown, cap, flashing, and masonry from the roof; a camera scan of the flue if the situation calls for one. Photos get taken throughout. At the end, you should receive a plain-language explanation of what was found, evidence you can see yourself, and a written scope if work is recommended. The whole process typically fits inside an hour or two. What you should not get is a verdict delivered from the driveway without anyone touching the chimney.

Fixing water intrusion is about sequence: seal the entry points from the top down, then protect the surfaces. That typically means crown repair or replacement first, since the crown is the chimney's roof; then a properly sized stainless cap to keep rain and animals out of the flue; then flashing — the layered metal where chimney meets roofline — repaired or replaced with counterflashing cut into the mortar joints rather than smeared over with roofing tar. Only after those are sound does waterproofing make sense: a vapor-permeable masonry water repellent that lets trapped moisture escape while blocking new absorption. Paint-like sealers that trap moisture inside brick actually accelerate freeze-thaw damage. Each layer protects the ones below it, which is why piecemeal fixes so often disappoint and a whole-system approach holds up for years.

Warning Signs to Watch For

Water stains on ceilings or walls adjacent to the chimney, especially after wind-driven rain.
Visible tar or roofing cement smeared around the chimney's base — evidence of a previous shortcut repair.
Rust streaks running from the chimney base down across the shingles.
Lifted, bent, or missing pieces of flashing after a windstorm.
Visible gaps between the counter-flashing and the mortar joint it should sit in.
Popped nails or loose fasteners along the flashing line.
Shingles that look wavy, curled, or spongy in the courses beside the chimney.
Attic sheathing that is dark, damp, or delaminating around the chimney — especially on its uphill side.
Leaks that appear during nor'easters but not during gentle vertical rain.
Moss or algae concentrated right at the roof-to-chimney intersection.

Why This Matters in Malden

Malden is a dense streetcar suburb of Victorians, triple-deckers, and two-families built between the 1880s and 1920s, with tight lots and tall brick chimneys that often serve multiple units. Many of these original stacks are unlined and have weathered a century of Boston-area winters. Neighborhoods near the Fells include larger single-family homes, while newer condo conversions raise questions about shared-flue responsibility.

Malden is literally next door to our Melrose headquarters, and its housing is nearly identical to what we work on at home: century-old multi-family chimneys on tight urban lots. Condo conversions across the city have left many shared chimneys with unclear maintenance responsibility, something we help associations sort out with documented inspections. When a Malden customer calls, we can often be there the same day.

The single greatest enemy of masonry in Malden is not fire; it is water paired with our freeze-thaw climate. Brick and mortar are porous, and every rain or melting snowfall lets moisture soak in. When temperatures drop below freezing, that trapped water expands roughly nine percent, prying the material apart from within. When it thaws, the water sinks deeper into the newly opened pores and waits to freeze again. Massachusetts winters can cycle above and below freezing dozens of times, and each cycle does its increment of damage. The visible result is spalling: brick faces popping off, mortar joints crumbling, and crowns cracking. Keeping water out of the masonry in the first place is why caps, crowns, and waterproofing earn their keep here.

What It Typically Costs

Chimney repair pricing varies more than sweep pricing because chimneys fail in such different ways and places. The main drivers are extent, access, and materials. Repointing a few mortar joints is a different undertaking from rebuilding a chimney from the roofline up. Work high on a steep roof may require staging that a walk-up ranch never would. And in the older neighborhoods we serve, matching brick and mortar appropriately matters, both for appearance and because modern mortar that is harder than antique brick can actually accelerate damage to the original masonry. A written estimate after an actual inspection is the only number worth trusting, and it should itemize the work plainly enough to compare against any other bid.

Why Call Upside Down Chimney Sweeps

Chimney work in New England is its own discipline. The housing stock around Greater Boston includes homes from nearly every decade since the Revolution, which means our technicians routinely encounter unlined flues, coal-era chimneys converted to gas, shared stacks serving multiple fireplaces, and brick manufactured to standards long since retired. Add a climate that freezes and thaws dozens of times each winter, and you have conditions no sunbelt training manual ever anticipated. Upside Down Chimney Sweeps works exclusively in this environment, so the judgment calls that matter most here, like when old mortar can be repointed versus rebuilt, or how to reline a flue without disturbing historic masonry, are calls we make every single week.

Frequently Asked Questions

What is chimney flashing, exactly?

Flashing is the layered sheet-metal system that waterproofs the joint where your chimney passes through the roof. Because the roof structure and the masonry move independently, no rigid or glued seal can survive there. Instead, flashing sheds water by overlapping: step flashing woven into the shingle courses carries water down the roof plane, and counter-flashing embedded in the chimney's mortar joints covers the tops of those steps so water running down the brick is thrown clear. Add an apron on the downhill face and a back pan or cricket uphill, and every side of the chimney has a gravity-fed drainage path. No adhesive is doing the real work — the geometry is.

What is the difference between step flashing and counter-flashing?

They are two layers with two jobs. Step flashing belongs to the roof: individual L-shaped pieces, one per shingle course, each tucked under a shingle and lapped over the piece below, fastened to the roof deck. It handles water flowing down the roof plane. Counter-flashing belongs to the chimney: pieces set into grooves cut in the mortar joints, bent down over the step flashing's vertical legs. It handles water flowing down the masonry face. The critical detail is that the two layers overlap without being attached to each other, so the roof and the chimney can move independently through the seasons without tearing the seal open.

Why not just seal it with roofing tar?

Roofing cement is a bandage, and everyone in this trade knows it. It bonds poorly to dusty masonry, turns brittle in the cold, shrinks away from edges within a couple of seasons, and — the part homeowners rarely hear — it can trap water behind it, holding moisture against the mortar through freeze-thaw cycles and accelerating the very damage it was hiding. It also buries the evidence, so the next diagnosis takes longer and costs more. We remove tar patches; we do not add to them. A proper counter-stepped metal system costs more on the day it is installed and dramatically less over the life of your roof.

Should I call a roofer or a chimney company for a flashing leak?

It is genuinely a boundary trade, which is why homeowners get bounced between the two. Roofers are excellent on the shingle side but often surface-mount counter-flashing with caulk rather than cutting it into the mortar, because masonry is not their trade. A chimney company that does masonry can cut reglets, repoint, and judge whether the leak is actually the crown or the brick rather than the flashing at all. We handle the full intersection and coordinate with your roofer when the job crosses into the roof field. Whoever you hire, ask one question: will the counter-flashing be let into the mortar joint? If the answer involves caulk, keep calling.

Which flashing metal is best, especially near the coast?

For most inland Greater Boston homes, aluminum or galvanized steel is serviceable and economical, but both have limits: aluminum reacts with damp mortar over time, and galvanized coatings fail early in salt air. Within a few miles of the ocean we push toward stainless steel or copper — coastal exposure corrodes cheap metal astonishingly fast, and we regularly replace galvanized flashing barely fifteen years old in shoreline towns. Copper is the premium choice everywhere: it forms beautifully, ages to a quiet brown, and routinely outlasts two shingle roofs. On historic homes in and around Malden, matching existing copper work is usually the right call both structurally and visually.

What is a cricket, and does my chimney need one?

A cricket, or saddle, is a small peaked structure built on the uphill side of a chimney to split water and snow around it instead of letting the chimney act as a dam. Modern building practice calls for one when the chimney is wider than about 30 inches across the slope. Without a cricket, the high side collects leaves, snowpack, and ponded water, and that standing load eventually beats any flat back pan. Many chimneys on older Massachusetts homes were built without one, which is why chronic high-side leaks are so common here. If your stains are on the uphill side of the chimney, ask us to check for this first.

How long does the repair take, and how long will it last?

Most full flashing rebuilds are a one-day job; targeted repairs of a single failed section often take a few hours. Weather matters — we want dry shingles, workable temperatures for sealants and mortar, and safe footing, so winter scheduling can shift with the forecast. As for longevity: properly counter-stepped metal set into sound mortar should last as long as the roof itself, and copper considerably longer. The honest caveat is the surrounding masonry — flashing set into crumbling joints will never reach its potential, which is why we repoint the reglet line as part of the job rather than treating it as an upsell.

My roof is being replaced — should the flashing be redone at the same time?

Yes, almost always, and the timing is a gift: with the shingles off, the entire intersection is exposed, membrane can be run properly, and new step flashing costs the least it ever will. Reusing old step flashing under a new roof is a common corner-cut we would talk you out of — thirty-year shingles deserve better than twenty-year-old metal. Coordinate the sequence: we can cut reglets and set counter-flashing right after the roofer finishes the field, or handle the full chimney intersection ourselves as part of the project. Call (781) 653-5644 before the roofing crew starts and we will slot the chimney work into their schedule.

Get It Handled Today

Here is our closing pitch, such as it is: no pressure, just an honest look. Call Upside Down Chimney Sweeps at (781) 653-5644 and schedule an inspection for your Malden home. We will examine the chimney from top to bottom, show you photographs of what we find, and give you a written assessment with a clear estimate for any recommended work. Then the decisions are yours, made on evidence, on your timeline, with no obligation beyond the visit itself. If you want a second opinion, we welcome the comparison; our documentation travels well. That is the whole offer. We think it is how chimney service ought to work, and we would be glad to prove it at your house.

Serving Malden Same-Week

Our Melrose shop is 3 miles from Malden. Call (781) 653-5644 for fast scheduling.

Call (781) 653-5644 Email Us

Mon–Sat: 7:00 AM – 7:00 PM · Emergency service available