Upside Down Chimney Sweeps logo
Call

Everett, MA · Middlesex County

Brick Chimney Sealing in Everett, MA

Brick and mortar drink water like a sponge — then New England winter freezes it. Our breathable siloxane treatments stop the absorption before spalling starts. Most chimney waterproofing treatments in the Boston area run $300–$750 depending on chimney size and roof access, with crown coating or minor repointing adding a few hundred more when needed.

Call (781) 653-5644

This article exists because "brick chimney sealing" deserves a better answer than the internet usually provides. Chimney topics attract two kinds of content: vague filler written by people who have never held a brush, and alarmist pitches designed to frighten you into a contract. We are aiming for a third kind — the explanation a good sweep would give you across the kitchen table. Upside Down Chimney Sweeps is a Melrose, Massachusetts company, and everything below comes from work we actually perform in Greater Boston homes: the causes we find, the inspection process we follow, the repairs that hold up through New England winters, and the honest way to think about cost. Read on, and if anything raises a question about your own chimney, our number is (781) 653-5644.

The stakes with chimney problems are not hypothetical. A chimney's core function is containment: keeping flue gases, sparks, and extreme heat inside a sealed passage until they exit above the roof. Carbon monoxide is odorless and colorless, and a blocked or leaking flue can push it back into living space instead of venting it outside. Meanwhile, creosote — the tar-like residue wood smoke deposits inside the flue — is fuel waiting for an ignition source, and chimney fires often burn unnoticed until they have damaged the liner or spread toward framing. This is why both NFPA 211 and CSIA guidance treat annual inspection as a baseline, not an upsell. Most chimney issues are discovered during a routine visit, long before they become emergencies. The dangerous ones are almost always the ones nobody was looking at.

Ask any experienced sweep to name the real enemy of chimneys and the answer will not be fire — it will be water. Masonry is porous. Rain and snowmelt soak into brick and mortar, and every time temperatures cross freezing, that trapped water expands roughly nine percent, prying material apart from the inside. In a Massachusetts winter, a single week can deliver several freeze-thaw cycles. The chimney's defenses against this — the crown on top, the cap over the flue, the flashing where brick meets roof, and breathable water repellents on the masonry face — all wear out on their own schedules. When any one fails, water gets in, and nearly every expensive chimney problem we see traces back to that moment. Whatever symptom brought you here, water is the first suspect worth ruling out.

Chimney Waterproofing & Sealing in Everett, MA

Set a dry brick in an inch of water and come back in an hour: the waterline will have climbed the brick like a wick. Masonry is a sponge — brick, mortar, and block all pull water inward through capillary action, and the portion of your chimney above the roofline gets wetted on all four faces by every storm that crosses Massachusetts. In summer, most of that moisture evaporates back out. From November through April it does something worse: it freezes in place, expands roughly nine percent, and pries the masonry apart from within — flaking brick faces, powdering mortar, and opening ever-larger pathways for the next storm to exploit. Chimney waterproofing exists to interrupt that cycle at its first step, by stopping the absorption itself.

The word waterproofing suggests paint or a rubber coating, and that is exactly what it must not be. Masonry constantly needs to release vapor — moisture from combustion, from condensation inside the flue, and from the house itself migrates outward through the brick. A film-forming sealer traps that vapor behind an impermeable skin, where winter freezes it and shears the brick face right off; chimneys sealed with the wrong product often spall faster than untreated ones. What we apply instead is a penetrating siloxane- and silane-based water repellent: it soaks into the pore structure and chemically lines the pores so liquid water cannot wick in, while water vapor still passes out freely. The chimney sheds rain like waxed canvas but continues to breathe.

Waterproofing is the finishing move of good chimney maintenance, never a substitute for repair. A repellent cannot bridge a cracked crown, fill an open mortar joint, or re-seat failed flashing — water pouring through a defect simply bypasses the treatment. So we sequence the work properly: repoint failing joints, repair or coat the crown, confirm the cap and flashing are sound, and only then flood-coat the masonry field. Applied to a sound chimney, a quality repellent keeps the brick dramatically drier through the freeze-thaw season, slows spalling to a crawl, starves efflorescence and moss of the moisture they feed on, and typically protects for eight to ten years before re-treatment is due.

What the Service Includes

1Pre-treatment condition assessment

We never spray a chimney we have not inspected. Before quoting waterproofing we examine the crown for cracks, the cap and flashing for function, the mortar joints for depth and hardness, and the brick faces for spalling — photographing all of it. If the masonry needs repair, we tell you and price it, because repellent applied over defects is money wasted. We also look for signs of internal moisture, like efflorescence patterns that suggest flue condensation, which waterproofing alone cannot solve. The assessment protects you from paying for the wrong fix.

2Vapor-permeable repellent application

We apply professional-grade siloxane and silane water repellents formulated for chimney masonry — never film-forming acrylic sealers. The material goes on as a flood coat, saturated from the bottom of the stack upward so the run-down soaks in evenly, followed by a second wet-on-wet pass that drives penetration deeper into the pore structure. Proper coverage rates matter more than brand names; a light misting fails early. Treated masonry beads and sheds rain while remaining fully breathable, and because the chemistry bonds inside the pores, it will not peel, blister, or discolor with UV exposure.

3Crown sealing and elastomeric coating

The crown — the sloped top surface that sheds water off the stack — takes more direct water than any brick below it, and hairline crown cracking is nearly universal on chimneys more than a decade old. As part of a waterproofing package we clean the crown, fill hairline cracks, and apply a flexible elastomeric crown coating that bridges movement through seasonal thermal cycling. Crowns that are structurally failed rather than surface-cracked get flagged for proper repair or rebuild instead — coating a collapsing crown just hides the problem for a season or two.

4Repointing and spall preparation

Repellent needs sound masonry to protect. Where we find scattered failing joints or a few spalled faces, we cut out and repoint the bad joints with compatible mortar and replace individual damaged bricks before treatment, giving new mortar time to cure before the flood coat goes on. Matching mortar hardness matters on the older homes around Everett — a hard modern high-Portland mix against soft historic brick transfers stress into the brick itself. Small repairs folded into the same project keep the chimney watertight as a system rather than sealing defects permanently in place.

5Efflorescence and stain removal

Those white, chalky blooms on brick are efflorescence — mineral salts carried to the surface by migrating water and left behind as it evaporates. Beyond looking bad, they are a map of your chimney's moisture problem. We clean efflorescence, algae, and organic staining with appropriate masonry cleaners and low-pressure rinsing — never aggressive blasting, which opens the brick's pores further. A repellent applied over heavy salt deposits bonds poorly; cleaned first, it penetrates properly. And because treated brick stays drier afterward, the staining largely stops coming back.

6The full water-management check

Waterproofing only earns its keep as part of a complete water-management system, so every job includes a check of the other components: cap present and correctly sized, chase covers free of ponding, flashing engaged in its mortar joints, and the flue itself free of the condensation clues that point toward a liner problem. Where something is wrong we document it with photos and price the fix separately — no bundling games. The goal is simple: every path water can take into your chimney is either shed, sealed, or flagged, and you know exactly where things stand.

How We Diagnose and Fix It

A thorough exterior diagnosis works from the top down, because that is how water attacks. The sweep starts at the crown — the concrete slab capping the chimney — checking for cracks, spalls, and improper construction like thin mortar-wash crowns that were never built to last. Next comes the cap and the condition of the flue tiles, then down the stack: mortar joint condition, spalled or shaling brick faces, staining patterns that map water paths, and finally the flashing where the chimney penetrates the roof, one of the most common leak points on any house. Each defect tells a story about sequence — which failure came first and what it caused next. That ordering matters, because repairing a downstream symptom while leaving the upstream cause intact is how homeowners end up paying for the same problem twice.

A well-run repair project follows a predictable arc. It starts with the inspection findings, documented in photos or video you can review yourself. From there, the contractor writes a scope: what will be done, with what materials, in what order, and what it costs — itemized so you can see where the money goes. Scheduling comes next, often shaped by weather, since masonry work has temperature requirements. On work day, expect drop cloths and dust control inside if the job touches the firebox or flue, and staging or roof access outside. Afterward, a reputable outfit walks you through what was done, ideally with after photos taken from the same angles as the before shots. For a project like waterproofing, that documentation trail is not bureaucracy — it is how you verify you got what you paid for.

Warning Signs to Watch For

  • Brick that darkens in the rain and stays dark for hours after the storm has passed.
  • White, chalky efflorescence blooming on the chimney's exterior faces.
  • Small flakes or popped faces of brick appearing on the roof or on the ground below.
  • Mortar joints that feel sandy or crumble when touched.
  • Hairline cracks spidering across the chimney crown.
  • Musty fireplace odors that come and go with humid weather.
  • Interior staining near the chimney that appears seasonally rather than after specific storms.
  • Moss, lichen, or algae colonizing the shaded faces of the masonry.
  • Frost blooming on the exterior brick during winter cold snaps.
  • A chimney that has never been treated, or was last waterproofed more than eight to ten years ago.

Why This Matters in Everett

Everett is one of the densest cities in the Commonwealth, built out almost entirely by the 1930s with triple-deckers, two-families, and closely spaced wood-frame singles. Most of these buildings carry original brick chimneys serving stacked heating appliances, and many flues have been switched from coal to oil to gas without ever being properly relined. Flat and low-pitch roofs are common, and access between buildings is tight.

Just four miles from our Melrose shop, Everett is home turf. The chimney story here is urban: aging multifamily stacks, gas-conversion liner work, and tall brick chimneys that loom over three stories of tenants who all depend on the same flue. Landlords and condo associations make up a big share of the calls in this city.

The single greatest enemy of masonry in Everett is not fire; it is water paired with our freeze-thaw climate. Brick and mortar are porous, and every rain or melting snowfall lets moisture soak in. When temperatures drop below freezing, that trapped water expands roughly nine percent, prying the material apart from within. When it thaws, the water sinks deeper into the newly opened pores and waits to freeze again. Massachusetts winters can cycle above and below freezing dozens of times, and each cycle does its increment of damage. The visible result is spalling: brick faces popping off, mortar joints crumbling, and crowns cracking. Keeping water out of the masonry in the first place is why caps, crowns, and waterproofing earn their keep here.

What It Typically Costs

The best defense against overpaying for chimney work is a contractor who shows their evidence, so here is what you should demand from anyone in our trade, including us. Ask to see photographs or video of the condition being repaired. Ask which part of NFPA 211 or the appliance manufacturer's requirements makes the work necessary rather than optional. Ask for a written, itemized estimate before work begins, and ask what happens to the price if hidden conditions appear. A reputable company answers all of this comfortably. Chimney work is invisible to the homeowner almost by definition, which is exactly why documentation, plain explanations, and written scope are not courtesies; they are the actual product.

Why Call Upside Down Chimney Sweeps

One thing homeowners appreciate about Upside Down Chimney Sweeps is that we handle the whole chimney, not just one slice of it. Sweeping, camera inspections, cap and damper replacement, crown repair, flashing, waterproofing, repointing, liner installation, and full rebuilds all live under one roof. That breadth matters because chimney problems rarely respect trade boundaries: a leak may involve the flashing, the crown, and the mortar joints all at once, and a company that only sells one fix tends to see only one cause. Because we diagnose and repair across the entire system, we can recommend the remedy the chimney needs rather than the one we happen to offer. Fewer handoffs also means one point of accountability from first call to final walkthrough.

Frequently Asked Questions

What is the difference between waterproofing and just painting or sealing the brick?
Everything. Paints and film-forming sealers sit on the surface as an impermeable skin. Masonry needs to release vapor — from combustion, from interior humidity, from moisture already inside the wall — and a film traps it at the surface, where winter freeze-thaw shears the brick face right off. Chimneys sealed with the wrong product routinely spall worse than untreated ones. True chimney waterproofing uses penetrating siloxane and silane repellents that line the pores inside the brick: liquid water cannot wick in, but vapor passes out freely, and nothing sits on the surface to peel or blister. If a product's label says waterproof paint or masonry sealer, it does not belong on a chimney.
How long does chimney waterproofing last?
Quality professional-grade repellents applied at proper coverage rates typically protect for eight to ten years, sometimes longer on sheltered stacks. Exposure drives the range: a tall chimney taking coastal wind and salt near the shore will need renewal sooner than an inland chimney partially shielded by trees or rooflines. The product does not fail all at once — the water-beading gradually diminishes as weathering depletes the outermost treated zone. That is one more reason the annual inspection habit pays off: a quick bead check tells us when re-treatment is due, and renewing on time costs a fraction of letting the brick absorb water through several more winters first.
Can you waterproof a chimney in cold weather?
There is a season for this work. Most repellents want surface and air temperatures above roughly 40 degrees, a dry chimney going in, and several rain-free hours after application — and fresh mortar repairs need proper curing conditions besides. In practice that makes mid-spring through mid-fall the working window in Massachusetts, and it is why we tell homeowners not to wait for October: the best time to waterproof is after winter's damage is repaired and well before the next freeze arrives. If you call in December, we will inspect, plan any repairs, and calendar the treatment for the first reliable stretch of suitable weather in spring.
Will waterproofing change how my chimney looks?
A properly chosen penetrating repellent is essentially invisible once cured — no gloss, no film, no color shift. Your brick looks like your brick; the difference only shows when it rains and water beads and sheds instead of darkening the masonry. During application the surface looks wet, and for a short period there can be a faint dampness to the appearance, but that passes as it cures. What many homeowners notice over time is what stops happening: the white efflorescence stops blooming, moss and algae stop colonizing the damp faces, and the chimney stays one color through a storm instead of turning dark and saturated.
My chimney already leaks — will waterproofing fix it?
Usually not by itself, and anyone who quotes it as a leak cure without an inspection is guessing. Active leaks overwhelmingly enter through defects — a cracked crown, failed flashing, an open flue without a cap, deteriorated mortar joints — and a repellent cannot bridge or fill any of those. What waterproofing does is stop the slow absorption through the brick field, which is a real but different problem. The correct sequence is diagnosis first, repair of the actual entry point second, and waterproofing last, as protection for the repaired system. That is exactly how we structure the work, and it is why our fixes hold through the following winters instead of reappearing each spring.
Is it worth waterproofing a chimney I barely use, like a gas or oil flue?
Yes — arguably more so. Freeze-thaw damage does not care whether you burn fires; it only needs rain and winter, and an idle chimney gets plenty of both. Lightly used flues in the older converted homes around Everett often suffer more moisture stress, not less, because cooler flue temperatures never dry the masonry the way regular wood fires once did, and modern appliance exhaust adds condensation from within. The masonry above your roofline is a structural element of the house regardless of what it vents. Protecting it is house maintenance, not fireplace maintenance — the same logic as painting trim on a porch you never sit on.
What does chimney waterproofing cost?
Typical single-flue chimneys in Everett and the wider Boston market run in the low-to-mid hundreds for cleaning, masking, and a two-coat application, with taller stacks, steep or complicated roof access, and larger multi-flue chimneys running toward $700 or somewhat beyond. Adding an elastomeric crown coat or minor repointing typically adds a few hundred dollars, priced for the actual work involved rather than as a bundle. These are typical ranges, not a quote — access and condition drive the real number, which is why we price after inspection. Set against the spalling and rebuild costs it prevents, it remains one of the highest-return maintenance dollars a homeowner can spend.
What actually makes brick spall, and does waterproofing prevent it?
Spalling is freeze-thaw mechanics. Brick pores fill with absorbed water; when temperatures drop, that water freezes and expands about nine percent, generating pressure inside the pore structure; the outer face of the brick — its hardest-fired, most weather-resistant layer — eventually fractures and pops off, exposing softer interior clay that absorbs water even faster. Each cycle compounds the last, which is why a chimney can look fine for forty years and then fall apart in five. Waterproofing prevents it the only way physics allows: by keeping water out of the pores in the first place. Where brick is already spalled, we replace the damaged units first, then protect the rest — call (781) 653-5644 to have yours assessed.

Get It Handled Today

What you are really buying from a chimney company is the ability to stop wondering. No more second-guessing the flue every time you light a fire, no more eyeing that stain on the ceiling near the chimney, no more resolving each October to deal with it next year. One call to Upside Down Chimney Sweeps at (781) 653-5644 settles the question for your Everett home: a professional sweep, an inspection guided by NFPA 211, photographs of everything relevant, and recommendations ranked honestly by urgency. Most chimneys pass with minor notes, and their owners sleep better for knowing it. If yours needs work, you will know exactly what and why. Either way, the wondering ends.

Serving Everett Same-Week

Our Melrose shop is 4 miles from Everett. Call (781) 653-5644 for fast scheduling.

Call (781) 653-5644Email Us

Mon–Sat: 7:00 AM – 7:00 PM · Emergency service available